The Stalker LED Spe
ed Signs
Next Generation High-Intensity LED Speed Signs
Available in 2 1/2- and 3 1/2-digit models
Stalker’s new Speed Signs use high-intensity LEDs with no moving parts to break or wear out and are thinner and lighter than their old-generation counterparts. These new Speed Signs do things that the old flip-signs can’t do, such as connecting up to three Speed Signs to a Pro II radar to simultaneously show Pitch, Plate, and Hit speeds.
- Lightweight and durable
- Stable swingout feet
- Folds flat for easy storage
- Hangs with integrated top corner hooks
- Bright, easy-to-read LED digits
- Bluetooth Capable
Stalker LED Speed Signs interface with all Stalker Sport Radar and Jugs Radar Guns through the use of connectors and dedicated cables.
- Stalker ATS II
- Stalker Pro II
- Stalker Sport 2
- Stalker Solo 2
- Stalker Sport
- Stalker Pro
- Jugs Pro-Sports
- Jugs Si Arcade
Stalker LED Speed Sign Setup and Configuration:
LED Speed Sign Setup
The Stalker LED Speed Sign features rotating feet that fold parallel to the sign’s case for easy storage. To position the Speed Sign on a flat surface, rotate the feet 90 degrees so that they are perpendicular to the sign’s face. Alternatively, hang the sign using the integral top-corner hooks.
Connecting a Radar and a Sign
In order for the Speed Sign to properly recognize the particular radar gun model and its data, the unit(s) should be connected in the following manner:
1) connect data cable to radar and sign
2) apply power to sign by connecting the external power supply*
3) power up radar
* EXTERNAL POWER SUPPLY IS NOT WATERPROOF. KEEP DRY AT ALL TIMES.
Speed Sign Controls
The Stalker LED Speed Sign’s controls are located on the lower left side of the unit. A momentary push-button switch initiates LED testing sequences in the following modes:
Push 1 – Table Demonstration Mode: Slowcount, full digit flash, slow count, fast count, loop...
Push 2 – Fast count
Push 3 – All LEDs on
Push 4 – Show software version
Push 5 – Enter normal mode
Configuration
To configure multiple LED Speed Signs using the Stalker Pro II radar, use Speed Sign multiple sign cabling hub, 200-0815-00. Set DIP switches 6, 7, and 8 to their appropriate positions before connecting the radar and signs.
Switch Position 2½-Digit Speed Sign
part number - 200-0778-00 3½-Digit Speed Sign
part number - 200-0779-00
Switch 1: ON Set to ON (↑) when K-Sport or Sport Pro output is TTL (data from bottom
of the handle). Set to OFF (↓) for all other radars.
Switch 2: ON 100% brightness.
Switch 3: Reserved Unused
Switch 4: Reserved Unused
Switch 5: ON,
Ignore Decimal Point The 2½-Digit LED Speed Sign ignores the decimal point and anything following. The 3½-Digit LED Speed Sign ignores anything following the decimal point. “123.4” is displayed as “123”. “1234.5” is displayed as “1234”.
Switch 6: ON Displays - Release Speed For bE format.
Switches select which
Speed Reading is displayed.
Switch 7: ON Displays - Plate Speed
Switch 8: ON Displays - Hit Speed
Default setting: All 8 switches OFF.
Switch Position 2½-Digit Speed Sign
part number - 200-0778-00 3½-Digit Speed Sign
part number - 200-0779-00 Switch 1: ON Set to ON (↑) when K-Sport or Sport Pro output is TTL (data from bottom
of the handle). Set to OFF (↓) for all other radars. Switch 2: ON 100% brightness. Switch 3: Reserved Unused Switch 4: Reserved Unused Switch 5: ON,
Ignore Decimal Point The 2½-Digit LED Speed Sign ignores the decimal point and anything following. The 3½-Digit LED Speed Sign ignores anything following the decimal point. “123.4” is displayed as “123”. “1234.5” is displayed as “1234”. Switch 6: ON Displays - Release Speed For bE format.
Switches select which
Speed Reading is displayed. Switch 7: ON Displays - Plate Speed Switch 8: ON Displays - Hit Speed Default setting: All 8 switches OFF.